Mace DVR0414 Especificaciones descargar pdf (Pagina 24)

Output Method.

If the number in RECORD is selected, recording will start

automatically when the DVR senses an alarm trigger input.

ALMOUT – Alarm Output. If the alarm output port is chosen,

it will trigger any connected equipment (on the chosen port)

when there is alarm input. DELAY is the length of recording

time after receiving an alarm trigger (possible settings of 10, 20,

30… 90 seconds). When the external alarm is canceled, the

system will lengthen the recording time automatically before

closing alarm and relay outputs. When Time 1 and Time 2 are

set to ON, the DVR will record during the set time ONLY if

triggered by an alarm. The beginning time should be earlier

than the ending time; the time set in Time 2 should be later than

the setting in Time 1.

CONTROL

This is the P/T/Z Control settings of this DVR.

In CH option select the channel whose settings you wish to edit, and on which a

PTZ camera is installed.

Choose the protocol of the corresponding pan-tilt decoder in PROTOCOL.

ADDR is the address of the corresponding platform decoder.

BAUDRATE select baud rate of the corresponding decoder.

SAVE your settings, and you can now control your cameras. (Note: If controlling

multiple PTZ cameras, you must use a PTZ Decoder-Splitter)

NETWORK

This is the setup of remote Network (TCP) connections to the

DVR.

For details on how to set the DVR on the network, go to Page 17

(Network Operations).

Playback Options Description:

MULTICAST： “Manager” users can monitor each channel

freely, and other users can only view after

them. Maximum of 5 users.

TCP Protocol： Any user can monitor any channel. If the

transmission is via Internet, TCP should be

chosen. Maximum of 2 users.

MOTION DETECTION

CH - Choose the channel you wish to edit.

TIMING – The amount of time the DVR will wait before triggering the alarm.

ALMOUT – (Alarm out) this sets the external alarm trigger by the DVR on/off.

SENS – Sensitivity will determine how sensitive the DVR will be to motion.

AREA – Navigate to ‘SET’ and press Enter, this will set up the masked / non-

masked areas (masked areas will not respond to motion, non-masked will be

monitored for motion). The setting area can be divided in 396 sections. Red

section means the current cursor position, and green section is the motion

detection area. The no color area is masked from motion detection. To mask /

unmask areas, press the Fn button. Then use the Direction

buttons to move cursor around the grid. Any grid-square you

move over will be masked from motion detection. Press Fn

again to set the area. For un-masking areas, do the same.

TIME 1 – Between the times you set, the DVR will record and

monitor motion (if set to ON)

Time 2 – You can set two different times of the day when the

DVR will monitor motion.

After changing settings to motion detection (turning it on/off as well), you must manually shut down the

recording on the channels you wish to record by motion. The DVR will update the settings, and turn the

channels back on when it detects motion.

MOTION DETECTION

CH 1

TIMING 30 SEC

ALMOUT OFF

SENS MID

AREA SET

TIME 1 12:00A-12:00A

OFF

TIME 2 12:00A-12:00A

OFF

CONTRO

CH １

PROTOCOL NONE

BAUDRATE ４８００

ADDR ０００

SAVE CANCEL

NETWOR

IP  192.168.000.111

SUBNETMASK 255.255.255.000

GATEWAY 192.168.000.001

NONITOR MULTICAST 

PLAYBACK MULFICAST 

SAVE CANCEL

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 38 39

Comentarios a estos manuales

Sin comentarios

Mace DVR0414 Especificaciones Pagina 24

Comentarios a estos manuales

Relacionado con productos y manuales para Grabadores de vídeo digital (dvr) Mace DVR0414